HP Mini Series Pure Sine Wave Inverter &Charger
♦ Ultra Low THD, Typically 7% Under Full Linear Load
♦ MPPT Solar Charger Controller Available
♦ Remote Control Available
♦ Battery Temperature Sensing For Increased Charging Precision
♦ Auto Gen Start Function For Off Grid System With Generator As Backup Power
- Feature of HP Series Inverter & MPPT & Charger
Features
♦ Smart Remote Control
♦ Support Solar Panel with MPPT Function
♦ Designed to Operate under Harsh Environment
♦ DC Start & Automatic Self- Diagnostic Function
♦ Compatible with Both Linear & Non-Linear Load
♦ Easy to Install & Easy to Operate & Easy to Solve
♦ Low DC Voltage Supports Home & Office Appliances
♦ Powerful Charge Rate Up to 120Amp, Selectable From 0%-100%
♦ High Efficiency Design & “Power Saving Mode” to Conserve Energy
♦ Battery Priority Mode, Designates the Inverter-Preferred UPS Configuration
♦ 13 Vdc Battery Recover Point, Dedicated for Renewable Energy Systems
♦ 8 Pre Set Battery Type Selector Plus De-sulphation for Totally Flat Batteries
♦ 4-step Intelligent Battery Charging, PFC (Power Factor Correction) for Charger
♦ 8 ms Typical Transfer Time Between Utility & Battery, Guarantees Power Continuity
♦ 15s Delay Before Transfer when AC Resumes, Protection for Load when Used with Generator HP MINI Pure Sine Wave Inverter/Charger Electrical Specification Inverter Output Power Rating 600W 1000W Continuous Output Power 600W 1000W Surge Rating(20s) 1800W 3000W Output Waveform PureSine Wave/Same as input(Bypass mode) Nominal Efficiency 80%(peak) Line Mode Efficiency <95% Power Factor 0.9-1.0 Nominal Output Voltage RMS 120Vac or 230Vac Output Voltage Regulation ±10%RMS Output Frequency 50/60Hz±0.3Hz Short Circuit Protection Yes,Current Limit Function(Full after 1sec) Typical transfer time 10ms(Max) THD Tapically<3%,Max 10% under full liner load DC Input Nominal Inout Voltage 12.0Vdc Minimum Start Voltage 10.0Vdc Low Battery Alarm 10.5Vdc/11.0Vdc Low Battery Trip 10.0Vdc/10.5Vdc High Voltage Alarm & Fault 16.0Vdc High DC Input Recovery 15.5Vdc Low Battery Voltage Recover 13.0Vdc Idle Consumption-Search Mode <25W when Power Saver on AC Charger Input Voltage Range Narrow:100-135VAC/194-243Vac Wide:90-135VAC/164-243Vac Input Frequency Range Narrow:47-55±0.3Hz for 50Hz,57-65±0.3Hz for 60Hz Wide:43±0.3Hz plus for 50Hz/60Hz Output Voltage Depends on battery type Charger Breaker Rating(120Vac) 7A 10A Max Charge Rate 20A to 25A+/-5A,depending on models Over Charge Protection Shutdown 15.7V for 12Vdc Battery type Fsat Vdc Float Vdc Gel U.S.A 14 13.7 A,G.M 1 14.1 13.4 A.G.M 2 14.6 13.7 Sealed Lead Acid 14.4 13.6 Gel Euro 14.4 13.8 Open Lead Acid 14.8 13.3 Calcium 15.1 18.6 De-sulphation 15.5 for 4hrs Remote Control Yes.Optional Bypass & Protection Input Voltage Waveform Sine wave(Grid or Generator) Nominal Voltage 120Vac 230Vac Low Voltage Trip 80V/90V±4% 184V/154V±4% Low Voltage re engage 90V/100V±4% 194V/164V±4% High Voltege Trip 140V±4% 253V±4% High Voltage re engage 135V±4% 243V±4% Max Input AC Voltage 150VAC 270VAC Nominal Input Frequency 50Hz or 60Hz(Auto detect) Low Freq Trip Narrow:47±0.3Hz for 50Hz,57±0.3Hz for 60Hz Wide:40±0.3Hz for 50Hz/60Hz Low freq re engage Narrow:48±0.3Hz for 50Hz,58±0.3Hz for 60Hz Wide:45±0.3Hz for 50Hz/60Hz High Freq Trip Narrow:55±0.3Hz for 50Hz,65±0.3Hz for 60Hz Wide:No up limit for 50Hz/60Hz High Freq re engage Narrow:54±0.3Hz for 50Hz,64±0.3Hz for 60Hz Wide:No up limit for 50Hz/60Hz Mechanical Specification Inverter Dimensions(L*W*H) 325*173*135mm/12.8*6.8*5.3〞 362*173*135mm/14.3*6.8*5.3〞 Inverter Weight 7.5KG/16.5Ib 11KG/24.3Ib Shipping Dimensions(L*W*H) 425*230*205mm/16.7*9*8〞 475*230*205mm/18.7*9*8〞 Shipping Weight 8.5KG/18.7Ib 12KG/26.5Ib Display Status LED Standard Warranty 1 Year -
Low Battery Trip Volt:
The Low Battery Trip Volt is set at 10.0VDC by default. It can be customized to 10.5VDC
AC Input Range:
There are different acceptable AC input ranges for different kinds of loads. It can be customized
from 184-253VAC to 154-253VAC.
Load Sensing Cycle:
The inverter is factory defaulted to detect load for 250ms in every 30 seconds. This cycle can be
customized to 3 seconds thru the SW3 on DIP switch.
Frequency adjust:
The frequency of the inverter is arranged by the Sw4.
The factory default configuration for 220/230/240VAC inverter is 50Hz,and 60Hz for 100/110/120VAC
inverter. While the output freq can be easily changed once a qualified freq is applied to the inverter.
Solar / AC Priority Setting:
Our inverter is designed AC priority by default. This means, when AC input is present, the battery wil
be charged first, and the inverter will transfer the input AC to power the load.
The AC Priority and Battery Priority switch is available upon request. When you choose battery priority,
the inverter will inverting from battery despite the AC input.
Different Series Inverter Selection Guide

YueQing YIYEN Electric Technology Co., Ltd is a professional manufacturer on Voltage Stabilizer, Inverter and UPS.
- Located in Liushi, WenZhou, which is a capital of electrical in China;
- We have been in Power industry for more than 7 years;
- Good quality ,Reasonable price;
- Accepted Retail if we have product in stock;
- Accepted Wholesale,Brand Agents,OEM,ODM and Can be Customized;
- Accepted Payment Type: T/T, PayPal, Western Union;
